• Home
  • /
  • Blog
  • /
  • Industrial Graphene: 7 Simple Ways to Choose the Right Grade

Industrial Graphene: 7 Simple Ways to Choose the Right Grade

Industrial graphene can help engineers develop stronger composites, conductive inks and more durable coatings. Do you need a dry powder your team can blend, a liquid dispersion that fits an existing formulation, or a concentrate designed for use in a resin? For a pilot run, format can matter as much as grade.

Hiyka’s graphene catalogue groups products into seven categories, from powders and nanoplatelets to coatings and composites. This guide follows those categories so you can narrow down your choices, ask the supplier better questions and design a trial that tells you whether the material is worth taking to production.

1. Choose graphene powder when you want formulation control

Dry industrial graphene powder gives you flexibility over the resin or solvent you use and the amount of additive you introduce. That flexibility is useful if your lab is comparing formulations or screening how a filler affects stiffness, electrical resistance or viscosity. Start with a batch that uses your current formulation, then compare it with batches that use the same ingredients and processing conditions as closely as possible, with carefully recorded changes in filler content.

How the powder disperses can shape the result. Clumps may raise viscosity or leave parts of a sample with very different properties. Before ordering, ask about particle size, sample preparation and compatibility with your mixing equipment. A smooth-looking blend can still give uneven results after curing, so take measurements on several specimens, especially if uniform conductivity is part of the brief.

Also ask how the powder is packaged and whether the supplier provides a safety data sheet for the grade. Review that sheet with your team before opening the sample so you can plan how to weigh, transfer and store it in your facility.

2. Compare graphene nanoplatelets by size and test method

Graphene nanoplatelets are thin stacks of graphene layers. Suppliers may describe a grade by the width of its platelets, their thickness or the number of layers. These are separate measurements. Two industrial graphene grades can have similar lateral sizes and behave differently in the same resin because their thickness, surface characteristics or dispersion differ.

If you are comparing Hiyka’s PureGRAPH Industrial Graphene grades, use the listed sizes to shortlist samples, then ask for the technical data sheets and the measurement method. A median particle-size figure such as Dv50 describes a point in a size distribution by volume. It helps to ask how wide that distribution is, especially if the material must pass through a filter or produce a smooth film.

Test the nanoplatelets in the shape and thickness your product requires. A thin injection-moulded part and a thicker cast panel may respond differently, even if they use the same polymer. For a reference on the measurements suppliers use to describe powders and dispersions, see ISO/TS 21356-1 on graphene characterisation and the National Physical Laboratory’s graphene measurement guide.

3. Select graphene oxide for compatible liquid systems

Graphene oxide (GO) contains oxygen-bearing groups that can help it disperse in water. For a water-based film, membrane or coating, an aqueous suspension can be a practical candidate for screening. Look at the solids content, pH and carrier before ordering. These details help you estimate how much liquid and solid material you are adding to the formulation.

Reduced graphene oxide (rGO) is another option in the industrial graphene family. Reduction can partly restore electrical conductivity, with results that depend on the material and how it was processed. If conductivity is the main goal, compare available grades using a test on the finished material. For a flexible film, for example, check its sheet resistance after drying and again after bending. This gives you a clearer picture of how the film will behave during use.

Watch what happens after the material sits for a day or through the normal storage window for your formulation. Changes in settling or viscosity can influence how consistently it coats or prints. For background on why GO and rGO behave differently, see the Royal Society of Chemistry review on the chemistry of graphene oxide.

4. Match graphene inks, pastes and dispersions to your equipment

An industrial graphene dispersion can be a useful starting point when your team already has a wet mixing or coating process. An ink or paste may suit a specific application method. Hiyka lists these formats together in its catalogue. Ask about the carrier, solids content, storage conditions and drying or curing requirements so you can decide which grade belongs on your trial list.

Picture a team prototyping a printed sensor on flexible plastic. An ink can look uniform in a cup and still spread too far on the film or lose conductivity when bent. Print a small batch on the actual substrate and measure line width, adhesion and resistance after drying. For a screen-printed paste, check whether it releases cleanly from the screen and whether the line stays intact through repeated prints.

The same questions apply to an industrial graphene slurry used for battery electrode research, although the measurements change. Check compatibility with the binder and coating line, then compare how evenly the electrode coats and how it performs against your current formulation in cell tests. Use the same active material and comparable electrode loadings so the results help you judge the additive.

5. Consider a graphene masterbatch for an existing resin line

An industrial graphene masterbatch is a concentrated blend that you dilute into a compatible base material. For manufacturers evaluating industrial graphene, it can simplify dosing when the carrier fits the production resin and processing conditions. Hiyka lists an epoxy resin masterbatch for coating applications. Ask whether the carrier and the intended dilution are suitable for your resin, hardener and cure schedule before including it in a trial.

It is easy to compare samples on the wrong basis here. If a supplier gives you a suggested masterbatch percentage, check how much graphene that delivers in the finished formulation. For example, adding 2% by mass of a concentrate that contains 10% graphene would deliver 0.2% graphene by mass in the final blend. The example is a calculation, and you can use the same method with the actual figures on your technical data sheet.

If the carrier is different from your base resin, consider a control that contains the carrier without the graphene, where feasible. For coatings, measure application viscosity and adhesion after curing. For a polymer moulding trial, check how the melt flows and how the finished part looks. A stable run matters because small gains in one material property may be outweighed by rejects or interruptions on the line.

6. Evaluate graphene coatings on the real surface

An industrial graphene coating trial starts with a clear description of the surface and service conditions. A steel bracket near the coast and a machine housing cleaned daily face different risks. In each case, document the substrate, surface preparation, film thickness and exposure. Then compare candidate coatings using those same conditions so that the results can guide a purchasing decision.

For corrosion protection, include the current coating as your comparison. Inspect adhesion and look for blistering, rust or damage around scratches after an exposure test relevant to your product. Include edges and joints where possible. A flat test panel is easy to prepare, but the areas where water gathers or handling damages the surface may tell you more about how the finish will perform in use.

If considering an industrial graphene additive for an existing primer, record any change in spray behaviour, cure and film appearance. Corrosion performance depends on the full coating system and how it was applied. For technical background, see the review of graphene-based materials in anticorrosion coatings.

7. Try a graphene composite when a blend already fits the job

A graphene composite combines a graphene-based material with a matrix such as a polymer or metal. Hiyka’s graphene composite range includes HDPE-based products and a graphene copper composite. An existing blend gives your team a defined starting material for evaluation, which can be helpful if the immediate goal is to test a component.

Let the part tell you what to measure. For protective packaging around sensitive electronics, check whether the finished part reaches your required surface resistance under the expected conditions. For a structural polymer component, compare stiffness and impact performance together. For an electrically conductive component, measure resistance in the geometry you intend to use and check whether it changes after the component has been assembled or aged.

Industrial graphene composites can also be candidates for heat management. If the finish or part needs to carry heat in a particular direction, measure performance in that direction. In a flat sheet, the ability to spread heat across the surface can differ from the ability to conduct it through the thickness. A trial on the assembled part can also capture the effect of contact between neighbouring surfaces. See the review of graphene–epoxy composites for thermal management.

How to run an industrial graphene trial before buying in bulk

Choose one result you can measure and one practical limit you need to respect. A coatings team might aim for less corrosion around a scratch while keeping the current cure time. An electronics team might aim for lower sheet resistance while retaining flexibility. A plastics team might look for higher stiffness while keeping impact performance within its specification. A short brief makes it easier to compare options and to ask a supplier for the data that matters.

For each industrial graphene sample, record the grade, batch number, additive content, mixing order and any changes to processing. Ask for the technical data sheet, safety data sheet and, where available, the certificate of analysis for the sample batch. Compare test methods alongside reported values. Conductivity measured on a film and conductivity measured on a pressed powder sample describe different specimens, which matters if you are ranking possible grades for a coating.

Use your current formulation as the control. Trial a small set of additive levels that your team can repeat and check the outcome again on a fresh batch. Pay attention to daily production details such as settling during a shift, changes in application thickness and the time needed to clean equipment. If a result matters to a customer specification, confirm it on representative parts before using it in product literature.

When a promising sample moves to pilot scale, record what changed between the lab and the line. The larger mixer may have a different design, the material may spend more time in a holding tank, and the drying conditions may vary across the coating width. Keep a sample from the lab trial for comparison and agree on the measurements that will determine whether the pilot run is ready for a purchase decision.

Finally, compare cost per usable part or coated area. Include the amount of additive used, extra mixing time, waste and the cost of any process changes. A useful industrial graphene grade meets the performance target at a cost the finished product can support. If two grades perform similarly, the one your team can dose and run reliably may offer greater value over a full production cycle.

Find the right starting point with Hiyka

If you want to adjust the properties of a working resin, start by comparing powders, nanoplatelets or a compatible masterbatch. For a water-based formulation, look at graphene oxide suspensions or other industrial graphene dispersions with a suitable carrier. If you need a printed feature, a protective finish or a part you can test directly, shortlist the relevant ink, coating or composite. Choose a small sample and test it against the material you already use.

When you enquire about industrial graphene, share the substrate or base resin, the equipment you use, the property you want to improve and the quantity you need for the first run. Those details give Hiyka a better basis for suggesting sample options and providing relevant technical documents. Browse the Hiyka industrial graphene range or contact Hiyka for a grade recommendation or quote.

To pick up a draggable item, press the space bar. While dragging, use the arrow keys to move the item. Press space again to drop the item in its new position, or press escape to cancel.

Drag to reorder pinned navigation items

To pick up a draggable item, press the space bar. While dragging, use the arrow keys to move the item. Press space again to drop the item in its new position, or press escape to cancel.

Get a quote