• Home
  • /
  • Blog
  • /
  • Graphene Conductive Slurry – 7 Practical Checks Before Your First Trial

Graphene Conductive Slurry – 7 Practical Checks Before Your First Trial

Graphene conductive slurry gives formulation teams a liquid way to introduce a conductive additive into a battery electrode, antistatic coating or polymer composite. If you have ever made two batches with the same ingredients and measured different resistance, you already know why dispersion matters. The way conductive particles spread, make contact and settle into the dried material can affect performance just as much as the amount you add.

Hiyka offers two graphene conductive slurry grades, nominally 4% and 10% conductive agent content. Choosing between them starts with knowing how much conductive agent your formulation needs, how much liquid it can accept and which measurement will tell you the trial worked. The seven points below take you from the product data sheet to a side-by-side test you can discuss with your team. View Hiyka’s graphene conductive slurry specifications.

1. A liquid dispersion gives you a starting point

A graphene conductive slurry carries conductive material in a liquid. The formulation team can weigh the slurry into a mix, following the supplier’s instructions, and check how it behaves with the other ingredients. That can simplify a first trial when the alternative requires a separate step to wet out dry powder. Once the slurry meets your binder, resin or active material, the behaviour of the combined mixture is what matters.

Graphene’s sheet-like geometry is part of the reason researchers study it as a conductive additive. A sheet can make contact with several nearby particles and help form a connected path through the material. The number and quality of those contacts depend on the whole formulation. During drying or curing, particles can shift as liquid leaves or resin sets, changing the paths available for current. A wet mix that looks smooth still needs an electrical measurement after processing. Read the Advanced Energy Materials review on conductive networks.

Take a simple coating example. Two samples look equally smooth when wet. After drying, the first gives similar readings at the centre and edges. The second has a few spots with much higher resistance. Measuring across the surface shows a difference that appearance alone would miss. For a technical buyer, that is a good reason to discuss the intended test along with the grade and sample size.

One practical check is to compare a freshly mixed sample with one held for as long as a normal production batch would wait before application. Record whether the mixture still flows as expected and whether any visible settling redistributes under the supplier’s recommended handling procedure. Then make and test a film from each sample. A difference between them can help you pinpoint whether time between mixing and coating matters for your process.

2. Compare the 4% and 10% graphene conductive slurry grades

Hiyka publishes appearance, conductive agent content, viscosity and particle size for both grades. The table gives you a starting point for planning how much slurry to add and deciding what to ask the supplier before opening a trial batch. Check the original Hiyka product listing.

Published propertyRN-6E-SE4101-4%RN-6E-SE4101-10%
AppearanceBlack liquidBlack liquid
Conductive agent content3.8–4.2%9.8–10.2%
Viscosity at 25 °C≤1,600 cP≤1,600 cP
Particle size D505.0–12.0 µm3.0–10.0 µm

Equal masses of the two grades deliver different amounts of conductive agent. At the nominal concentrations, for illustration, 25 grams of the 4% slurry and 10 grams of the 10% slurry each supply about 1 gram of conductive agent. Use the actual batch figure when available. Confirm the carrier and other ingredients with Hiyka so you can account for the slurry’s effect on the finished formulation.

Both grades share the same published viscosity ceiling. Ask how the supplier measured viscosity and then check how the full mix flows under your own process conditions. D50 is the midpoint of the measured particle size distribution on the basis used in the test. If your process has fine filters or narrow gaps, ask about the larger particles and clusters in the distribution. Record which grade and lot you use so the comparison can be repeated later.

3. Test battery electrodes under comparable conditions

In a lithium-ion electrode, the conductive additive helps electrons move between active material particles and the current collector. That makes the layout of the conductive network important. Poor contacts can leave parts of the electrode harder to reach electrically. A battery development team evaluating graphene conductive slurry can start by asking whether its electrode reaches the target resistance at a practical loading and still meets coating requirements. Read the review of carbon conductive networks in lithium-ion batteries.

Keep your current electrode recipe as the control. Compare it with a trial that replaces part of the existing conductive additive, where appropriate. Record the dry conductive agent loading, active material loading and electrode thickness. Keep your coating, drying and compaction conditions comparable where feasible, and record any changes needed for the trial. Then look at resistance alongside adhesion and visible coating defects. A low-resistance film that peels from the current collector would still need more development.

Electrode resistance is an early measurement. Rate capability, cycle life and other cell-level outcomes need separate testing in the intended cell design. Plan those tests around how the cell will be used. For instance, if the cell must deliver power quickly, decide what discharge rates it needs to handle and compare the trial with your control under the same conditions.

4. Work to the resistance range your antistatic coating needs

An antistatic coating for an electronics work surface has a different job from a conductive additive in a battery electrode. The coating may need to dissipate static charge in a controlled way as part of a wider electrostatic discharge (ESD) control programme. Start with the resistance range and test method specified for the application. Then use those requirements to choose which trial samples merit a second round. See the EOS/ESD Association’s guide to static control procedures and materials.

When screening graphene conductive slurry in a coating, use the substrate and cure conditions you expect in production. Note the dry-film thickness and take readings at several points. If a technician will wipe the surface daily, check resistance after representative cleaning. If the part will be handled frequently, consider testing after wear. Record temperature and relative humidity at the time of measurement where the test method calls for it.

Imagine a coating that meets your target on day one and shows higher resistance after several cleaning cycles. The first reading tells you the material can reach your initial target. The later reading tells you something changed under use. Check the film condition, adhesion and measurement setup before changing the formulation. Those observations help you decide whether another trial is worthwhile.

5. Judge polymer composites by the finished part

Graphene conductive slurry can change how a polymer composite carries current. The shape and thickness of the finished part also matter. If you want current to move along the surface, choose a measurement that captures that path. If current needs to go through the material, test through its thickness. Record the moulding or coating direction and sample thickness so you can compare parts on the same basis.

When evaluating graphene conductive slurry in a resin, confirm the carrier’s compatibility and check whether it changes cure behaviour or the condition of the finished part. Look for visible clumps or defects and record any change in mixing or application. If the part has a mechanical job, check the properties that matter to that use. A formulation may hit the resistance target and still need work to meet adhesion, flexibility or strength requirements.

For electromagnetic interference (EMI) shielding, measure shielding effectiveness across the frequencies the component needs to handle. An electrical resistance reading can help you narrow the candidates before you run that test. Where the composite will be used as an enclosure, include relevant details such as joints and seams in later evaluation. Hiyka lists advanced composites and EMI shielding among the applications to explore. See Hiyka’s application overview.

6. Give every trial batch the same scorecard

Start with a control and a few graphene conductive slurry loading levels that fit your formulation. Compare the grades at equivalent conductive agent loadings where practical, and account for the different amounts of liquid introduced. For each batch, note the grade, lot, mixing sequence, hold time and how the mixture looked before application. Use the same measurement method and conditions for all samples in the comparison. Take the same measurements on more than one test piece so a single smooth or thick sample cannot drive the decision.

What to recordWhat it helps you decide
Total slurry added and dry conductive agent loadingWhether samples contain comparable amounts of conductive agent
Flow during mixing and applicationWhether the formulation fits your equipment and method
Resistance at several locationsWhether the electrical result is consistent across the sample
Adhesion, surface finish and visible defectsWhether the sample meets physical requirements alongside resistance
Results after a relevant use conditionWhether the performance holds up during expected handling or service

Sheet resistance, commonly reported in ohms per square (Ω/□), is one way to compare thin conductive films. Write down the test method and film thickness so readers can interpret the numbers. If you move from a bench drawdown to a production coating line, recheck the same properties on a pilot run. Differences in mixing equipment, application speed or drying can change the film you produce. See an ACS Nano study that reports sheet resistance for graphene-based coatings.

Ask the supplier for the current technical and safety data sheets and any available certificate of analysis for the sample lot. Confirm the carrier, recommended handling, storage and shelf life for the grade you plan to use. If several people will run trials over time, write the grade and lot on the sample labels and keep the documentation with the results. When results differ, the batch record gives you somewhere to start.

During the review, keep photographs of representative samples alongside the readings. A photo of edge defects or uneven coverage can help explain why a batch with an acceptable average still needs another look.

7. Choose a grade around the limits of your process

Which graphene conductive slurry should you sample first? If your recipe has little room for extra liquid, the nominal 10% grade delivers more conductive agent per gram of slurry. If your process can accommodate the carrier and you are working at a small addition level, the nominal 4% grade may give you a larger amount of liquid to weigh for the same target. You can confirm the practical benefit by comparing both grades in your system. Compare the two grades on the Hiyka product page.

When planning a pilot, decide which measurements would justify a larger order. An electrode team might set targets for resistance and adhesion while tracking cell test results separately. A coatings team might prioritise consistent surface resistance after cleaning. A composite team might check electrical performance and mechanical properties on the same set of test parts. Agree on these targets before you compare samples so your lab and purchasing teams can use the same criteria.

If your purchasing team compares quotes, put the grades on a common basis. Estimate how much slurry each formula would consume per batch at the target conductive agent loading. Then consider the work needed to prepare and apply it, the amount of usable coating or material you get and whether the supplier can provide the batch documentation you need. This makes the price comparison more meaningful than looking only at the cost per kilogram of slurry.

Ready to evaluate graphene conductive slurry for your product? Tell Hiyka what you are making, the substrate or active material you use, your application method and the electrical result you need. Include your planned trial size and any limits on carrier, viscosity or drying. Ask for the relevant product documents, sample availability and a quote for the grade you want to evaluate. Request a sample or quote from Hiyka.

To pick up a draggable item, press the space bar. While dragging, use the arrow keys to move the item. Press space again to drop the item in its new position, or press escape to cancel.

Drag to reorder pinned navigation items

To pick up a draggable item, press the space bar. While dragging, use the arrow keys to move the item. Press space again to drop the item in its new position, or press escape to cancel.

Get a quote